Love Solution

Hers the solution for Nokia 6700s slide Not charging problem issues like charger no response or no charging indication when the battery charger is plug-in. This solution shows the location of the chip fuse,a diode a resistor that need to check or replace when charger no response occurred.
There is a 0 ohms Resistor located beside the vibra motor. that also needs to check also when the fuse and the diode is okay.

Heres a brief solution for Nokia 7230 No network signal problem. This solution shows the RF circuit on nokia 7230 that holds the radio signal  during data transmission.
Please note before you may use this solution, first ensure that the device firmware is totally calibrated, successfully flashed or restored and upgraded or downgraded. This solution below covers only for hardware failure that may not or cant be fix by software or firmware. The Nokia 7230 RF circuit components mounting is similar to Nokia X6. This solution below is from Nokia X6 board. 

Just follow the instructions indicated on the solution above of which and where to start in  troubleshooting proceedings. In most common cases the RF Power Amplifier breakdown may most often causes the problem.

This solution may help fix if the Nokia C5 shows "charger not supported error when the battery charger is plug-in. If the error message shows, this probably cause by a faulty hardware components on Nokia C5 PCB board.

Just refer to the solution below and locate the highlighted components for it is part of  the charging indication components.
Hints for repair a Nokia C5 charger not supported problem:
1. Try to use another phones battery and charger.
2. Check/clean the battery terminals and connector
3. Check/ replace the 47K resistor as shown on the solution above

Nokia C2-06 Blank Lcd Display, Nokia C2-06 White Lcd Display, Nokia C2-06 Lcd Jack Damage Prints Missing.
Tools:-
To solve lcd display problem in Nokia C2-06 we have required a few tools and components.
Nokia screw Driver t5 and t4 for opening screw .
Lcd panel for Nokia C2-06
Electronics Cleaner for rust or water damage.
Hot air to dry the mother board.
Lcd Jack if we have to replace it.
 


Diagnosting & Solution:
After disassemble of Nokia C2-06 remove lcd and check lcd jack and its near by area for rust or water damages.
If here is some carbon on parts or at lcd jack.
Apply electronics cleaner and dry it with hot air for a few mint.
Do not apply so much heat it can harm your skin and mother board parts also.
Check with Lcd and if it is still blank replace with new one.
It might be possible that lcd jack pins are missing or not getting connected with lcd so change it.
Check all these links as given in above diagram in different colors so that you can find them easily.
Warnings:
Do not apply to much heat it can damage the mother board.
Make sure mother board is dry proper when you apply electronics clean.
Check Lcd jack and when removing it make sure solder has been melt.
If solder has not proper melt and you try to remove lcd jack prints might be damage.
When you replace lcd make sure lcd strip is proper fixed.
It can be damage when you assemble the phone if not in proper place.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update daily this blog timely with other mobile solution.

NOKIA N8 MMC PROBLEM: NOKIA N8 MMC PROBLEM REPAIRING SOLUTION IMAGE CONTAINS MEMORY CARD PROBLEM REPAIRING INSTRUCTION.

This Solution may also works for Nokia 2710 FM radio and GPS problem.

NOKIA 1110 LIGHT REPAIRING:NOKIA 1110 LIGHT PROBLEM REPAIRING SOLUTION SHOWN IN THE IMAGE.

Nokia C2-06 ringer HF is not working, Nokia C2-06 Ringer Speaker is not working, Nokia C2-06 can not play music. We can not here voice during loud speaker in nokia c2-06.
Tools:-
Nokia key T4 and T5
Hot air.
Solding Iron.
Electronics Cleaner.
Nokia C2-06 Ringer

Diagnostic & Solutions:-
If Nokia C2-06 is not abble to ring a bell and we can not use loud speaker it might be fault of ringer or it may not be attached with mother board.
it can be damage or might be its not in proper location.It can be cause of Water damages and missing components,So lets solve the problem in a few simple steps as given in above diagram.
Disassemble Nokia C2-06 and check ringer points with electronics meter.If ringer shows good value then check point on the mother board and if the have also a good value it can be cause of miss fitting.
So assembly with proper placements and tight the screw and try it if not working then replace ringer with new one.If you find some prints missing then apply jumpers as given in above diagram. There are two different color lines Red and Blue.These lines indicates the negative and positive prints of ringer in Nokia C2-06 so apply these jumper to solve ringer problem in nokia C2-06
Warnings:-
Do not apply much heat with hot air it can damage the mother board and your skin.
Keep in mind about placement of ringer because it is not proper ringer will not work.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update daily this blog timely with other mobile solution.

Nokia Asha 300 ringer problem can be solve with a few steps that are given in diagram bellow so look at diagram bellow to solve love ringer voice, no ringer tones, no ringer working problems in nokia asha 300.in diagram there are two colors blue and red both colors are defining path of circuit in mobile phone.

Check ringer and if ringer do not show continuity or a good value with meter then change ringer with new one. Check points on board where ringer have to attaché after put in casing housing.
Then check all these paths as shown in diagram above and if any of them is broken or missing components then apply jumpers as described above. Small circle shows positions where we are able to make jumpers. in these place we can apply jumpers to solve ringer problem in nokia asha 300.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update daily this blog timely with other mobile solution.

if Nokia C2-06 MMC is not working or it do not accept memory card it can be cause of water damage and rust. It can be due to MMC jack and damage pins. And this problem can be reason of MMC I.C So lets check all these parts and try to Repair Memory card Problem in Nokia C2-06.


The above diagram have a red line to show you which parts are used in Memory Card function so check these parts and in first step try to clean them with electronics cleaner and apply some hot air to dry it.
Once it is dry check and if not working then replace this I.C to solve memory card problem in Nokia C2-06. 

Nokia C5-00 get water damage and it is not getting power on due to shortage.To solve this problem look at diagram bellow and find the capacitor that is given in it nokia Asha 311 Power Button On Off Switch Not Working Problem

Clean the mother board where ever you find carbon or rust in it.Dry it with hot air and do not apply too much heat because it can harm your skin and may can damage the Nokia C5-00 Mother board.
If it can not be OK with cleaning the board for shortage in Nokia C5-00 you may can remove this capacitor and it will be fine.
The Nokia c5-00 Shortage problem would be solve and it will power on easily without shortage.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update daily this blog timely with other mobile solution.